1 IG300BT C1/C2 Area image Barcode Scanner Quick Start Guide
10 3.4.1 Set Scanner Pin Code Mode Set Default Security Code <PINCODE = 000000> Set Security Code ON <Set Security code OFF>
11 3.5 Bluetooth Cradle Setup 3.5.1 Set Cradle Security Mode Set Default Security Code Barcode <PINCODE = 000000> Set Security ON &l
12 4. Configuring 4.1 Preface How to configure this device: The Barcode Programming Feature gives the possibility to change the scanner setting
13 4.3 Changing Scanner Settings with Utility Tool Manufacturer has setup this scanner with the most common used programming codes, It could be po
14 5. Operating Settings 5.1 Factory Default Set Scanner /Cradle factory default The scanner and cradle factory default settings are shown wit
15 Pulse A reading session begins when beam is activated and stays on until a period of inactivity lasting the time specified by the timeout. Afte
16 Toggle This mode allows lighting and decoding toggle when the trigger line is activated. First trigger activation = lighting and decoding on,
17 5.3 Imager Mode You can set the best reading performance depends on the environment, your used application and type of barcodes. Linear mod
18 5.4 Sleep Mode The scanner is equipped with sleep mode function to save battery energy when the scanner is not used for 1 minute or 10 minute.
19 Out Of Range Memory Mode ON <Memory Mode OFF> Memory Read Memory Clear 5.6 Firmware Version Display the firmware ve
2 Conents 1. Introduction ... 4 1.1 Illustration ... 4 2. Installation ...
20 5.6.4 Scanner Bluetooth MAC Address 5.6.5 Cradle Bluetooth MAC Address 5.7 Set Cradle Interface Barcode Set Cradle KB Interface Barc
21 9600 <19200> 38400 5.8.2 Cradle Data Bits 7 data bits <8 data bits> 5.8.3 Cradle Stop bits <1
22 Even Odd 5.8 Decoding Selection 5.8.1 Symbologies Selection Australian Post ON <Australian Post OFF> AZTEC ON <AZTEC OFF
23 <CODABAR OFF> Codablock A ON <Codablock A OFF > Codablock F ON <Codablock F OFF > CODE 11 ON <CODE 11 OFF> <COD
24 CODE 128 OFF <GS1-128 ON> GS1-128 OFF <DATAMATRIX ON> DATAMATRIX OFF Dutch Post ON <Dutch Post OFF> <EAN-8 ON> EA
25 EAN 128 OFF GS1 CC-A/B ON <GS1 CC-A/B OFF> GS1 CC-C ON <GS1 CC-C OFF> GS1 DataBar-Omni ON <GS1 DataBar Omni OFF > GS1 Da
26 <Infomail OFF> Interleaved 2 of 5 ON <Interleaved 2 of 5 OFF> Japan Post ON <Japan Post OFF> Matrix 2 of 5 ON <Matrix
27 <MSI OFF> <PDF417 ON> PDF417 OFF Planet ON <Planet OFF> PLESSEY ON <PLESSEY OFF> Postnet ON <Postnet OFF&
28 <QR Code - model 1 OFF>
29 <UPC-E ON> UPC-E OFF 5.9 Disable All Symbologies. If you want to disable all Symbologies, please scan below programming code. Or y
3 5.6 Firmware Version ... 19 5.7 Set Cradle Interface Barcode ... 20 5.8 Cradle RS232 Mode Parameter ...
30 5.10 Multi Code The multicode function is used configure the scanner to read a series of bar codes and then transmit them all at once. <
31 Data Format: [UDSI symbology id] <data> Symbology Default Identifier Australia Post P3 Aztec D3 BPO P2 Canada Post P6 Codabar B7 Co
32 Matrix 2 of 5 B4 MaxiCode D2 MicroPDF417 C8 MSI Code B8 PDF417 C7 Planet P1 Plessey Code C2 Postnet P0 QR Code D1 Standard 2 of 5 B5 S
33 5.12 Postambles The scanner can be programmed to output Barcode data according to the following format: [BAR CODE DATA] [POSTAMBLE STRING] P
34 Appendixes A. Readable Symbologies 1D Symbologies Symbologies Readable Default Enable EAN/UPC ○ ○ UCC/EAN128 ○ ○ ISBN ○ ISBT ○ Code 11 ○ Co
35 2D Symbologies Symbologies Readable Default Enable Data Matrix ○ PDF417 ○ ○ MicroPDF417 ○ MaxiCode ○ QR code ○ Aztec ○ EAN.UCC composite ○
36 C. Indicator LED Status a) Cradle Light Signal Status Green 1 blink good read and transmitted Red continuous on power on off power off Blue 2
37 D. Electrical Characteristics Operation Voltage 5 VDC ±5% Current Operating 450 mA (max) @ 5 VDC Current Standby 37 mA typical @ 5 VDC AC tran
38 UPC / EAN 0.33 mm 4 cm 31 cm Data matrix 0.191 mm 5.3 cm 16.2 cm 0.254 mm 3.8 cm 21 cm 0.381 mm * 28 cm PDF417 0.16 mm 5.2 cm 14.4 cm 0.254 mm
39 Interleaved 2 of 5 MSI code PDF417 GS1 DataBar Omnidirectional GS1 DataBar Omni Stacked GS1 DataBar Expanded GS1DataBar Expanded St
4 1. Introduction Thank you for purchasing this brand-new designed 2D imager hand held barcode scanner. This is a cutting-edge gun-type Area Imag
5 2. Installation 2.1 Unpacking 1) Take device and its accessories out of the box. 2) Remove the packing material. 3) Check the standard sh
6 IG300BT Cradle 1) Connect the supplied communication cable at the bottom side of the scanner and you will hear a “click” when the connection is ma
7 Cable Installation Connect cable and adaptor to Cradle. The other end of cable will be connected with Host device. Lock the iron panel of Cradle
8 3. Set up Bluetooth Communication Before the operation, Bluetooth Communication must be set up between the scanner and cradle. 3.1 Pairing Eac
9 ATTENTION: It is important to know that the scanner will only communicate with the cradle with the unique Bluetooth MAC address. Other scanner ca
Kommentare zu diesen Handbüchern